Mechanical

AF 1.0" Mechanical Seam Panel Profile

Panel Information

Panel Type Standing Seam
Panel Seam Mechanical
Panel Width 17''
Seam Height 1.0''
Panel Material 22 ga--24 ga min
Panel Surface Smooth / Embossed Optional
Minimum Slope 3/12

Panel Notes

This panel uses a 20'' coil. Maximum width coil of 20''.
This panel uses 3'' of material to form the panel.
If you take the square footage of the roof and multiply that by 1.18, the total will be the amount of coil needed the manufacture the panels.
Suitable for zinc and copper.

AF 1.5" Mechanical Seam Panel Profile

Panel Information

Panel Type Standing Seam
Panel Seam Mechanical
Panel Width 16''
Seam Height 1.5''
Panel Material 22 ga--24 ga min, .032
Panel Surface Smooth / Embossed Optional
Panel Clip Required Per Engineering
Minimum Slope 2/12
Substrate Plywood, B-Deck, B-Deck w/ISO

Panel Testing

Uplift Resistance UL 580, UL 1897, UL 90
Air Infiltration ASTM E 1680
Water Penetration ASTM E 1646
Water Submersion ASTM E 2140*
Hail Rating Class 4 Impact UL 2218
Fire Rating UL Class A
Texas Department of Insurance Approval RC-386*, RC-395*, RC-397*
FBC Non-HVHZ Approval FL18316*

Panel Notes

With this panel engineering, you. may opt to use heavier gauge coil and narrower width panels. Clip spacing will not change.
For slopes lower than a 2/12 roof pitch, contact SMI Technical Department for further installation direction and requirements.
This panel uses a 20'' coil. Maximum width coil of 20''.
This panel uses 4'' of material to form the panel.
If you take the square footage of the roof and multiply that by 1.25, the total will be the amount of coil needed the manufacture the panels.
This panel is approved for Weathertight Warranties.

 

* Available in steel only.

AF 2.0" Mechanical Seam Panel Profile

Panel Information

Panel Type Standing Seam
Panel Seam Mechanical
Panel Width 18'' (Steel) / 16'' (Aluminum)
Seam Height 2.0''
Panel Material 22 ga--24 ga min, .040
Panel Surface Smooth / Embossed Optional
Panel Clip Required Per Engineering
Minimum Slope .5/12 (Steel) / 2/12 (Aluminum)
Substrate Open Framing*, Plywood, B-Deck, B-Deck w/ISO

Panel Testing

Uplift Resistance ASTM E 1592*, UL 580, UL 1897, UL 90
Air Infiltration ASTM E 1680
Water Penetration ASTM E 1646
Water Submersion ASTM E 2140*
Foot Traffic FM 4471*
Hail Rating Class 4 Impact UL 2218
Fire Rating UL Class A
Texas Department of Insurance Approval RC-383*, RC-384*, RC-385*, RC-390*
FBC Non-HVHZ Approval FL18316*

Panel Notes

With this panel engineering, you. may opt to use heavier gauge coil and narrower width panels. Clip spacing will not change.
For slopes lower than a 2/12 roof pitch, install sealant per ASTM E 2140.
This panel uses a 24'' coil (Steel) / 22'' Coil (Aluminum).
This panel uses 5-13/16'' of material to form the panel.
If you take the square footage of the roof and multiply that by 1.34, the total will be the amount of coil needed the manufacture the panels.
This panel is approved for Weathertight Warranties.

 

* Available in steel only.

Available Colors

Environmentally Smart Colors -- Designed Energy Efficient

  Terra Cotta

  Aged Copper

  Solar White ♣

  Sandstone ♣

  Surrey Beige

  Colonial Red ♣

  Patina Green

  Regal White ♣

  Ash Gray ♣

  Sierra Tan ♣

  Regal Red ♠

  Hemlock Green ♠

  Stone White

  Dove Gray

  Medium Bronze ♣

  Burgundy ♠

  Hartford Green ♣ ♠

  Slate Blue

  Slate Gray ♣

  Mansard Brown ♣

  Matte Black ♣

  Evergreen ♣

  Regal Blue ♣ ♠

  Charcoal Gray ♣

  Dark Bronze ♣

Metallic Colors

  Silver ♣

 

  Copper ♣

 

  Champagne ♣

 

  Pre-Weathered

  Galvalume® ♣

Non-Painted

 Acrylic Coated

 Galvalume®

Weathered Colors

  Galv-Ten™ ♦

 

  Copper-Ten™ Raw ♦

 

  Cor-Ten AZP® ♦

 

  Vintage®

 

♣  --  Available at a slight price premium.    ♠ --  Available in 26ga SMP    ♦  --  Also available in Robust.

 

 

Colors shown are matched as accurately as possible, but may vary slightly from finished product. These rich and vibrant colors are produced with either Kynar 500 or Hylar 5000 resins, which provide superior color retention and allow Sheffield Metals to offer non-prorated coating warranties for most applications. Coating warranty varies for Regal Red, Matte Black, Copper, Champagn, Silver, and Pre-Weathered Gavalume. Steelscape's Vintage carries a 20 year Finish Warranty. Please contact your representative for more information.

Galvalume is a registered trademark of BIEC International, Inc.  |  Hylar 5000 is a registered trademark of Solvay Solexis, Inc.  |  Kynar 500 is a registered trademark belonging to Arkema Inc.  |  Cor-Ten AZP is a registered trademark and the USS in Circle, Weathered Metal Series, Galv-Ten, and Copper-Ten are trademarks of United States Steel Corporation. All trademarks are used under the license of the United States Steel Corporation.

➤